MPI Matco

1-800 975-8273

SAF15 Ultimate
Two Component Methacrylate

 

SAF15 Ultimate is made of methacrylate adhesives, which brings a structural adhesion without the use of a primer. It offers high adhesive strength, high elongation as well as a low linear shrinkage of about 1%. It has the capabilities to resist impacts, vibrations and peeling.

It is recommended to use this product in temperatures varying between -40 and 150°C. It is also resistant to humidity during the assembly, UV effects as well as fresh, salt or demineralized water including permanent immersion. It has also obtained the M1/F1 accreditation for fire and smoke resistance. SAF15 Ultimate can withstand aggressive environments such as alkaline, diluted acids, polar solvents, oils and more.

Range of application

The SAF15 Ultimate is recommended for the following substrates:

  • Glass 
  • Metal such as aluminum, steel and all types of alloys
  • Technical plastics such as ABS, PMMA, acrylics, PVC, polycarbonate
  • Laminated glass/ resin; polyester ( including DCPD), vinyl ester, epoxy with or without gel coat, as well as SMC/BMC. 
  • Tender or stiff wood like teak, 

Key Features

  • High environmental and impact resistance 
  • Metal bonding 
  • Non-sag on vertical surfaces
  • Permanent toughness even after ageing
  • Minimal surface preparation
  •  High impact

Application

Optimum qualities are obtained at room temperature, ideally between 18°C and 28°C without post-curing.

For Use with

Packaging

The SAF15 Ultimate adhesive is available in 50mL and 490mL side by side cartridges, 20L pails or 200L drums.

  • SAF15 Ultimate 50ml cartridges require the use of
    ADH_M5.4/16 mixers.
  • SAF15 Ultimate 490mL cartridges require the use of
    ADH_MFX1318 or ADH_MFX1018 mixers.

Product Characteristics

System
Two component 4:1 Volume Ratio
Polymerization
Room Temperature
Final Colour
Dark yellow opaque

Adhesive Properties

Physical Properties Resin
Tensile Strength at Break (MPa)
6.0
Elongation at Break
200%
Hardness (Shore D)
45 - 50
Curing Properties
Open Time [min]
8
Working time (min) At 25°C
13
Full Cure [hours]
24
Temperature range
-40 to +200°C
Liquid Properties
Specific gravity (20°C)
Resin
0.98
Hardener
1.198
Viscosity (Pa.s) At 23°C )
Hardener
50
Dynamic - Resin*
1200
*Thixotropic – Non-sag on vertical surfaces
Mechanical Properties
Lap Shear strength
With NF 1465
PSI
Mpa
Aluminum 6060
13.0*
1 885.5*
Steel
13.0*
1 885.5*
*Cohesive Failure

Adhesive Selection Guide

Product
Key Features Specificity Mix Ratio
(Vol.)
Viscosity
Open Time(1)(mins)
Fixture
Time(1)
(mins)
Elongation (%)
Lap Shear
Strength (MPA)
Modulus (MPA)
SAF
Ultimate 5
Ultra fast curing for all types of material
1/10
Non-sag
1-2
3-5
50
12
300 - 400
SAF
Ultimate 15(2/3)
High strength resistance,
High impact resistance
1/4
Non-sag
8
10 -15
200
14
200 - 300
SAF
Ultimate 10(2/3)
Metal Bonding, High impact
resistance, Fast curing.
1 / 10
Non-sag
5-6
10
100
19
550 -750
SAF
Ultimate 25(2/3)
Metal bonding, High impact
resistance, Medium curing
1/10
Non-sag
15
25
200
17
400 - 500
(1) @23°C
(2) Homologated BV Marine for structural applications
(3) Homologuated EN45 545, HL3 for R1 requirement
Scroll to Top